Filthy AF

Southeast Traders Apparel Swag Store

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
I pulled the Gemtech 9mm can apart last night for it's first cleaning in about 1000 rounds...fuck. Had to (gently..kinda) pound the baffles out with a deepwell socket with small extension attached to it. I've never had baffles so stuck. It was pretty dirty, but damn.

I used a brass wire wheel on the dremel to remove carbon from the edges of the baffles to aid in re-assembly...mostly worked.

Any tips or tricks? Just don't clean them? lol
 

Mac11FA

Disgruntled large member
Super Moderator
Lifetime Supporter
Patriot Lifetime
Mar 26, 2015
3,840
3,011
113
Locust Grove, GA
Zip code
30248
Tumble the baffled? Not sure. What kind of ammo were you shooting? What kind of fouling did you see?
 

Mac11FA

Disgruntled large member
Super Moderator
Lifetime Supporter
Patriot Lifetime
Mar 26, 2015
3,840
3,011
113
Locust Grove, GA
Zip code
30248
Spray Pam on the baffles and inside the tube before reassembly
 
  • Like
Reactions: Laufen

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
Tumble the baffled? Not sure. What kind of ammo were you shooting? What kind of fouling did you see?
I've shot mostly CCI Lawman 147's and a handful of Freedom Munitions 147's.
 

Mac11FA

Disgruntled large member
Super Moderator
Lifetime Supporter
Patriot Lifetime
Mar 26, 2015
3,840
3,011
113
Locust Grove, GA
Zip code
30248
I've shot mostly CCI Lawman 147's and a handful of Freedom Munitions 147's.
Those are both jacketed bullets. I can't run the flat nose stuff with 100% consistency on the Mac. I have probably shot about 500 to 700 rds full auto thru my Gemtech. Guess I better disassemble and see how bad it is.
 

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
Those are both jacketed bullets. I can't run the flat nose stuff with 100% consistency on the Mac. I have probably shot about 500 to 700 rds full auto thru my Gemtech. Guess I better disassemble and see how bad it is.
Yeah the scorpion doesn't care what the bullet profile is it eats everything.
 
Last edited:

Mac11FA

Disgruntled large member
Super Moderator
Lifetime Supporter
Patriot Lifetime
Mar 26, 2015
3,840
3,011
113
Locust Grove, GA
Zip code
30248
I took the Gemtech apart tonight and didn't even try to force the baffles out. Soaking in the ultrasonic cleaner and will see if they loosen up enough to slide out easily.
 

Leshaire

Weekend Warrior
Mar 27, 2015
3,343
1,994
113
Acworth
Zip code
30102
I just dont clean mine lol. Ill pay someone to do it eventually. I dont have the proper equipment to really clean them well anyways so fuck it.
 
  • Like
Reactions: dial1911

chance

Tracker
Jul 15, 2015
958
1,073
113
Ga
Zip code
30101
Ultrasonic cleaner works decently, but a wet tumbler with ss pins will make them look new again (for stainless baffles only not aluminum)
 
  • Like
Reactions: Laufen

Laufen

Beloved flaming retard
Lifetime Supporter
Mar 23, 2015
7,927
6,129
113
I85
Zip code
30030
Ultrasonic cleaner works decently, but a wet tumbler with ss pins will make them look new again (for stainless baffles only not aluminum)
All but my blast baffle is aluminum, so no ultrasonic either. Goof Off graffiti cleaner does a surprisingly good job though.
 

Leshaire

Weekend Warrior
Mar 27, 2015
3,343
1,994
113
Acworth
Zip code
30102
I dont have a stainless tumbler yet. I can bead blast them though. Only takes a couple minutes and they will look brand new
My Tirant is a steel blast baffle and aluminum otherwise. I think my spectre II is all steel though. Can you bead blast both metals?
 

chance

Tracker
Jul 15, 2015
958
1,073
113
Ga
Zip code
30101
My Tirant is a steel blast baffle and aluminum otherwise. I think my spectre II is all steel though. Can you bead blast both metals?
Tirant should have a few titanium baffles, then some aluminum. Spectre is stainless. I can bead blast stainless and ti, but itll strip the anodizing off the aluminum
 
  • Like
Reactions: Leshaire

Leshaire

Weekend Warrior
Mar 27, 2015
3,343
1,994
113
Acworth
Zip code
30102
Tirant should have a few titanium baffles, then some aluminum. Spectre is stainless. I can bead blast stainless and ti, but itll strip the anodizing off the aluminum
Oh shit, well that likely means Ive been assembling my Tirant incorrectly since day one lmao