What say you, 9mm can suggestions?

Southeast Traders Apparel Swag Store

SouthernSlammed

Gingerbeard Operator
Lifetime Supporter
Aug 29, 2015
3,107
2,616
113
Fapville
Zip code
31061
So, with the current wait times, I thinK I need to start planning for a 9mm can for my SET AR9 build. The plan is to run it under the handguard. I'm planning on 10" handguard with a 5.5" barrel.

Would need to be:
< 1.375" in diameter
1/2 x 28 thread
< 8" in length


I was liking what I was reading on:
AAC Ti-Rant 9 -- but it's a little too big in diameter
AAC Illusion 9 -- But I would imagine that the offset would not work in the handguard


So, I'm interested now in possibly:
Griffin Armament Resistance 9

or
Gemtech GM9

WHAT SAY YOU?
 
  • Like
Reactions: Mac11FA

SouthernSlammed

Gingerbeard Operator
Lifetime Supporter
Aug 29, 2015
3,107
2,616
113
Fapville
Zip code
31061
Of course, then again, if I'm thinking of a 45acp upper in the future maybe I should look at a 45 can!

DAMN IT!!!

Or is there not enough suppression for 9mm out of a 45 can?
 
  • Like
Reactions: permaneo vox

dial1911

Waiting for the flash
Site Supporter
Jul 15, 2015
7,331
27,066
113
Anywhere but here
southeastoutdoors.boards.net
I've got a Tirant-9 and like it. Honestly, I can't tell much difference shooting it vs. the Guardian 9 (much cheaper- but also looks cheap).

I don't recall the specs on it, but it doesn't seem that big around.

And .45 out of an Octane HD .45 is slightly louder than 9mm out of the Tirant or Guardian... however, it's not noticeable to me. It's kind of like saying this guy slammed a door a little louder than that guy.

I have no first hand knowledge, but if you could get a 9mm end cap for the .45 can, it would probably be about the same.
 

Rwjeter

Space Force General Freeze.
Kalash Klub
Lifetime Supporter
Nov 16, 2016
5,354
10,815
113
Temple
Zip code
30179
Of course, then again, if I'm thinking of a 45acp upper in the future maybe I should look at a 45 can!

DAMN IT!!!

Or is there not enough suppression for 9mm out of a 45 can?
They say the Rugged .45 Obsidian is pretty damn quiet on a 9mm even with the .45 cap. And it's diameter is 1.37....
 
  • Like
Reactions: SouthernSlammed

Red Dawn

Wolverines
Site Supporter
Lifetime Supporter
Aug 12, 2015
5,743
6,957
113
H Town
Zip code
30228
Is it that the long setup is for 45 and short more towards 9mm?

What is the piston for?
Long is quieter with more baffles stacked and the short config is lighter but a touch louder. That goes for 9 or 45 either one

The piston is for shooting on pistols because the barrel moves you need the piston. On straight barrels PCC no need for it but you'll need the adapter to replace the spring.

If you plan on 45 get a 45 rated can and shoot both or you'll end up with 2 cans later.

Research all and weigh out the pros and cons of each. Watch videos and listen to the sound it makes. Pick the one you like
 

Red Dawn

Wolverines
Site Supporter
Lifetime Supporter
Aug 12, 2015
5,743
6,957
113
H Town
Zip code
30228
I have the Tirant 9s you are welcome to shoot btw. It's the short configuration only. I lost some of the sound suppression because I wanted a lighter can. AAC has a modular one now SiCo has Omega and Omega K.
 
  • Like
Reactions: SouthernSlammed

Rwjeter

Space Force General Freeze.
Kalash Klub
Lifetime Supporter
Nov 16, 2016
5,354
10,815
113
Temple
Zip code
30179
Also, some of the .45 cans are rated for .300 BLK subs. I think the Dead Air is, and I KNOW the Rugged is.
 
  • Like
Reactions: SouthernSlammed

Allsmiles

Frontiersman
Site Supporter
Kalash Klub
Mar 15, 2017
335
517
93
Golfcart City, GA
Zip code
30269
I run a TiRant45 on my AR9. Of course, it has a 16" barrel, so not really an issue and it is nice to swap pistons and run it on both 9mm pistols and 45 acp. Check the thread pitch on the barrel you are looking at as it may determine what can you get.
 
  • Like
Reactions: SouthernSlammed

NWS

Not a hot midget
Administrator
Lifetime Supporter
Mar 24, 2015
2,468
2,489
113
Georgia
Zip code
30172
@DoglegArms has a smoking deal on a few cans right now. The Innovative Arms Shepard comes to mind for what you are wanting to do.
 
  • Like
Reactions: Rwjeter

Rwjeter

Space Force General Freeze.
Kalash Klub
Lifetime Supporter
Nov 16, 2016
5,354
10,815
113
Temple
Zip code
30179
@DoglegArms has a smoking deal on a few cans right now. The Innovative Arms Shepard comes to mind for what you are wanting to do.
The only issue with that is the OD. The Shepherd is 1.5". He needed no more than 1.375". But it IS a screaming good deal. Also, @SouthernSlammed , watch your barrel thread pitch. I know you listed 1/2x28, which is most 9mm pistols, but a lot of 9mm PCC's are 1/2x36. I know Ballistic Advantage offers both thread pitches in a 5.5"
 
  • Like
Reactions: SouthernSlammed

Willy Leadwell

Purveyor of Polyurethane
Lifetime Supporter
Mar 26, 2015
2,159
1,679
113
Loganville, GA
Zip code
30052
You're welcome to play with the Octane 9 and the Revolution 45 if you can get over my way one day. I've been very happy with both of those purchases. The Octane 9 is perfectly at home under the rail of my SBR.
 
  • Like
Reactions: SouthernSlammed

NWS

Not a hot midget
Administrator
Lifetime Supporter
Mar 24, 2015
2,468
2,489
113
Georgia
Zip code
30172
The only issue with that is the OD. The Shepherd is 1.5". He needed no more than 1.375". But it IS a screaming good deal. Also, @SouthernSlammed , watch your barrel thread pitch. I know you listed 1/2x28, which is most 9mm pistols, but a lot of 9mm PCC's are 1/2x36. I know Ballistic Advantage offers both thread pitches in a 5.5"


Ah, missed the OD requirement. I know he had the IA 9SX too. It is 1.375".
 

Mac11FA

Disgruntled large member
Super Moderator
Lifetime Supporter
Patriot Lifetime
Mar 26, 2015
3,840
3,011
113
Locust Grove, GA
Zip code
30248
So, with the current wait times, I thinK I need to start planning for a 9mm can for my SET AR9 build. The plan is to run it under the handguard. I'm planning on 10" handguard with a 5.5" barrel.

Would need to be:
< 1.375" in diameter
1/2 x 28 thread
< 8" in length


I was liking what I was reading on:
AAC Ti-Rant 9 -- but it's a little too big in diameter
AAC Illusion 9 -- But I would imagine that the offset would not work in the handguard


So, I'm interested now in possibly:
Griffin Armament Resistance 9

or
Gemtech GM9

WHAT SAY YOU?
Get the Gemtech 9 can! Talk to @DoglegArms for a great deal. It is what I ordered for a dedicated can for the Mac and I love it.
 
  • Like
Reactions: SouthernSlammed

Leshaire

Weekend Warrior
Mar 27, 2015
3,343
1,994
113
Acworth
Zip code
30102
I also vote for the Tirant 9. I love mine. I run it under a handguard on an AR9 as well. Barrel is 4" if I remember right. I had to go with the ALG rail to make it fit. It was the only relatively cheap option to fit the can under it. I think it sounds great, is easily serviceable, parts are easy to come by and cheap ish...

C488730D-942C-4856-83EE-F6420C2DA054.JPG