Cree LED Light Bar

Southeast Traders Apparel Swag Store

HossHeir

Hunter
Aug 6, 2015
18
5
18
Shady Dale, Ga
My LED light bar. Finally got her installed. Only 60 bucks on Amazon. I had to make rubber spacers to put under the mounts. Made them out of the heel of a old boot.
4b0e1a5ce8978b7f27d5cf26c8597926.jpg
41b04618fc6da83ed15465fd797606fa.jpg
9c9d2fd9b47a165503fde27254c3b9b8.jpg




Sent from my iPhone using Tapatalk
 
  • Like
Reactions: Green Panther

HossHeir

Hunter
Aug 6, 2015
18
5
18
Shady Dale, Ga
How hard was it to wire up?
It wasn't too bad. It came with about two feet of wire coming off of it and those are wrapped in a thick rubber skin. I ran that through the roof of the truck with a rubber gromet. Also you need a fusible link, a relay, and a switch. But really, it wasn't bad.


Sent from my iPhone using Tapatalk
 

AtlMedic

Not A Doctor
Mar 25, 2015
2,644
1,441
113
Smyrna, GA
Zip code
30082
I've read the inexpensive ones have bad seals might be worth looking into pulling it apart and resealing the lense. Otherwise let us know how you like it, been wanting to pick up a couple for my truck.
 

HossHeir

Hunter
Aug 6, 2015
18
5
18
Shady Dale, Ga
I've read the inexpensive ones have bad seals might be worth looking into pulling it apart and resealing the lense. Otherwise let us know how you like it, been wanting to pick up a couple for my truck.
Yeah. I was thinking about running silicon around the seals. But I'll let you guys know!


Sent from my iPhone using Tapatalk
 

AtlMedic

Not A Doctor
Mar 25, 2015
2,644
1,441
113
Smyrna, GA
Zip code
30082
Give us some night shots to see how bright it is after the sun goes down. I'm curious how much throw it has since the high beams on my truck suck.
 

HossHeir

Hunter
Aug 6, 2015
18
5
18
Shady Dale, Ga
9a827e820ffa5d2f5a1f97f2ef4ef66f.jpg

Fuse got so hot that it melted, but didn't pop. I swapped out the "hot" wire for bigger ones and it seems to stay cool now.


Sent from my iPhone using Tapatalk
 
  • Like
Reactions: Hoss
H

Hoss

Guest
9a827e820ffa5d2f5a1f97f2ef4ef66f.jpg

Fuse got so hot that it melted, but didn't pop. I swapped out the "hot" wire for bigger ones and it seems to stay cool now.


Sent from my iPhone using Tapatalk
You need a heavier duty fusable link
 
H

Hoss

Guest
I saw someone say that the lower the gauge of the wire, the cooler it will stay. Seems to be true so far


Sent from my iPhone using Tapatalk
Yep, lower gauge = bigger wire. You need to find out what that light bar is pulling and wire it accordingly.
 
  • Like
Reactions: jwtug

Hayata

Blam-blam-blam-blam-blam-blam-blam-blam-PING!
Kalash Klub
Lifetime Supporter
Jul 5, 2015
6,135
30,134
113
Zip code
30022
9a827e820ffa5d2f5a1f97f2ef4ef66f.jpg

Fuse got so hot that it melted, but didn't pop. I swapped out the "hot" wire for bigger ones and it seems to stay cool now.


Sent from my iPhone using Tapatalk


Did you smell it cookin' or did you just check it on your own?

Wow, good thing you found it!
 

AtlMedic

Not A Doctor
Mar 25, 2015
2,644
1,441
113
Smyrna, GA
Zip code
30082
So, a couple things, Make sure that the wire is the same gauge the entire run and that the
It actually cut off. That's when I checked. I don't know why it cut off though, the fuse was intact.


Sent from my iPhone using Tapatalk

looks like the insulation melted off the wire which caused it to ground out before the fuse. Just a guess.
 
H

Hoss

Guest
It actually cut off. That's when I checked. I don't know why it cut off though, the fuse was intact.


Sent from my iPhone using Tapatalk
P=IV always

If that's a 300 watt light bar it will pull between 20-25 amps. You need to write it accordingly.