Primary weapons system ratchet castle nut

American Revival Apparel Company

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
anyone tried it? seems liek a great way to avoid staking and I have run into a few loose buffer tubes.
https://www.rainierarms.com/primary-weapons-systems-ratchet-lock-sling-mount-plate-and-castle-nut
primary-weapons-systems-ratchet-lock-sling-mount-plate-and-castle-nut-4btrlpb1-by-primary-weapon-systems-d13.jpeg
 

AtlMedic

Not A Doctor
Mar 25, 2015
2,644
1,441
113
Smyrna, GA
Zip code
30082
I guess if your removing the buffer tube often it may be worth it but I don't see the need since staking isn't hard and I doubt I'll have to remove my buffer tube anytime soon.
 

PewPewPewCo

Sniper
Mar 23, 2015
2,139
1,075
113
Georgia
I guess if your removing the buffer tube often it may be worth it but I don't see the need since staking isn't hard and I doubt I'll have to remove my buffer tube anytime soon.

I take it off pretty often due to the size of my ultra sonic cleaner
 

Righter13

Student of life
Lifetime Supporter
Mar 24, 2015
1,788
1,165
113
Greenville SC
Zip code
17268
I have one on my Noveske build and it works fine.

I'll be taking it through a course next week.
 

Cudruln

Turning dollars into pennies.
Lifetime Supporter
Jul 5, 2015
4,337
4,579
113
Rockmart, GA
Zip code
30153
I could use this, as I currently do not stake my castle nut.


On a side note is there really a big reason for staking the castle nut?
 

Righter13

Student of life
Lifetime Supporter
Mar 24, 2015
1,788
1,165
113
Greenville SC
Zip code
17268
I could use this, as I currently do not stake my castle nut.


On a side note is there really a big reason for staking the castle nut?
I have had a castle but or two come loose on me. It only takes a couple minutes to stake them.
 
  • Like
Reactions: Cudruln

boss_hawg

Marksman
Jul 13, 2015
1,230
1,045
113
Zip code
30328
i stake all of my end plates because if it comes loose you'll have problems.

having said that - i have a couple of these ratcheting sets and they seem to work well.

pws makes quality stuff so i have peace of mind that they won't loosen.

also, i like to change out my setup to a fixed stock every once in a while. this allows me to go back and forth without needing a new end plate every time (the previous stake marks bug me because i'm ocd like that).

also if i decide to throw an a5 system in down the road, it's easy to reuse these parts.
 
  • Like
Reactions: Righter13

Wallace

Tracker
Trusted Trader
Mar 26, 2015
828
370
113
Cartersville
Zip code
30145
Interesting design. Would like to see a long/ or high use results on this? Wonder if BF Las Vegas has them?....lol

Per the TM, you should stake your end plate/castle nut in two locations, after applying Aeroshell 33ms (TM advises molybdenum disulfide grease, which 33ms is close enough to be used) to the threads of the castle nut and receiver threads, then tightening to 40 +/- 2 INCH/lbs. If you are swapping stock sets alot and not rocking full auto a crap load between swaps, you can get by without staking for the most part IF you don't use 33ms on the threads.

That said, 42 inch pounds is not very much. after lubricating the threads, just tighten until nice and firm, not gorilla tight, then stake. Should have little to no worries, even if on an select fire lower.
 

freedom

Sniper
Mar 25, 2015
1,522
885
113
Covington, Ga
Zip code
30014
How many end plates could you replace for the cost of one of those?

I've had two come loose, back before I used to check stuff before shooting it.
 
  • Like
Reactions: Strider12

Righter13

Student of life
Lifetime Supporter
Mar 24, 2015
1,788
1,165
113
Greenville SC
Zip code
17268
How many end plates could you replace for the cost of one of those?

I've had two come loose, back before I used to check stuff before shooting it.
Idk about repalcement costs but these also feature a QD end plate.

A BCM end plate alone will run around $16/17

Brownell's standard end plate is $5 and casltenut for about $3

So my math says I'm paying about $7-9 more to be able to have a ratchet system.

Pws=$27.95

BCM end plate plus castlenut = approx $19/20
 
  • Like
Reactions: freedom

boss_hawg

Marksman
Jul 13, 2015
1,230
1,045
113
Zip code
30328
How many end plates could you replace for the cost of one of those?

I've had two come loose, back before I used to check stuff before shooting it.

probably four or five of the standard end plates.

but, maybe only one or two of the nicer end plates with a qd socket (like this one). i'm very happy with my purchase.